IN;TALLATION INSTRUCTIONS
PLEASE READ All Installation Instructions and Requirements Before Installing.
4. ADJUST LEVELINGFEET STEP_I,AOJUSTtEVEUNGFEET FINAL CHECKOUT
Your washer is equipped with self stabilizing legs on the rear
which automatically stabilize the unit. y_
The front legs are threaded and can be adjusted up and down to
• Have all installadol
level your unit. ,OCKW,S,E,
w,r,,,,os requirements been
Proceed as follows: rOC.ECK,_
s_e_E observed?
a. Position your washer as close to its final operating location
as possible. - _'_ _1 LeG" • Have locknuts on
b. Make sure rear feet move up and down freely, tooK,u, both front feet
been tightened
c. Place washer in final operating position, root_A° and are foot pads
d. Tilt machine forward until rear of cabinet is approximately 4 in place?
inches off the floor, turn the machine loose letting it fall on
the rear feet. This operation will cause the rear stabilizing feet • Are there any kink.,
to conform to the contour of the floor and seat them solidly, in hoses?
Rock washer with hands on opposite corners to check StEP_ D_A_NHOSETODRA_
stability.
-_ _=, ._ • Are any water lea_'
FRONT FOOT ADJUSTMENT FOR SIDETO SIDE LEVELING. eveident?
(IF MACHINE IS NOT STABLE) '_i_ • Plug the power cor,
a. Loosen the locknuts on each leg, making sure they turn _,,I__IE__
freely on the threads. . .. into an outlet?
b. When the machine is in place, screw front feet out of base s_L_.w, s_Lc...-
against the floor until the washer is acceptably level across • A protective plastk
the front. SE_',CEu,,_ t,O,O_TUB film may cover
C. While holding foot still, turn the adjusting lockout clockwise _. _ control panel.
until the _ocknut is tightened firmly against base. Repeat step • This should be
4d above. _ removed.
5. DRAIN HOSETO STANDPIPE " Start the washer in
STYLE A: Push the cuff on the gooseneck end of the drain hose T, wash cycle, as per
into the standpipe as far as possible. Do not seat drain hose and Operating
standpipe as an airtight seal will cause siphoning (fill problems). Instructions. AIIo-_
STYLE B: Put the gooseneck end of the drain hose into the STEP_ HOT AND GOLD FAUCETS water to fill in
standpipe or laundry tub.The drain hose should fit loosely in your _>._ c>-.__ machine until it
standpipe as there is a possibility of siphoning if it fits too tightly. "-_1_:::___._/_ reaches the bottom
NOTE: If you must make an airtight seal, an anti-siphon break kit _ row of holes in the
must be used. wash basket.
BOTH: To prevent accidental dislodging, secure the drain hose
to the standpipe, laundry tub or inlet hose with the TIE STRAP I I • To stop washer, pu
provided. _ i(_ w_,s.E, in on timer knob. l
the water is not lev
NOTE: BE SURE THE DRAIN HOSE IS NOT TWISTED OR _ _--_ ..... i with the bottom ra
KINKED. I t of holes all around
6. HOT AND COLD FAUCETS the basket, readjus
Push the screens and washers (provided in the parts bag) into the leveling feet as
the remaining ends of the water hoses. Attach the water hoses to required to level.
the hot and cold faucets. BE SURE ROT WATER INLET IS CON- ........... Remove the water
NECTED TO HOT WATER FAUCET. Tighten by hand until snug, • Putting washer int_
and then a _ turn with pliers. DO NOT OVERTIGHTEN. Turn on spin cycle.
faucets and check for leaks. Tighten to stop leaks, if necessary.
• During spin check
drain system for
leaks and proper
operation.
(3 pages)
(20 pages)
(24 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels